THERMAL ANALYSIS OF ROTATIONAL MOULDING PROCESS: AN APPLICATION TO MULTILAYER MOULDING

Authors

  • Raghav Bansal Department of Mechanical Engineering, BITS Pilani K.K. Birla Goa Campus, Zuarinagar, Goa-403726, India
  • Sachin Waigaonkar Department of Mechanical Engineering, BITS Pilani K.K. Birla Goa Campus, Zuarinagar, Goa-403726, India

Keywords:

LLDPE, PA-11, Heaviside Function

Abstract

Rotational Moulding is one of the fastest growing technologies in the processing of thermo-plastics. Multilayer products obtained by this process find extensive application in automobile components, particularly in fuel tanks. The process is characterized by a complex nature of heat transfer involving several phase changes. This paper presents a transient thermal simulation of the process for multilayer moulding of Linear Low Density Polyethylene (LLDPE) and Polyamide -11 (PA-11). FEM based COMSOL software is used for analysis and Heaviside function is used to model the phase changes over a range of temperatures. The cycle time, time required for phase transitions, time required for optimal curing temperature and demoulding time have been found out.  It takes approximately 66 minutes to complete the cycle. The study can be useful to rightly tune the process to achieve the optimal quality characteristics of the part with reduced energy consumption.

 

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

References

Bracewell R (2000), "Heaviside's Unit Step Function H(x)”, The Fourier Transform and Its Applications, Third Edition, New York: McGraw-Hill, pp. 61-65.

Brien G O, Partridge R and Clay B (2004), “New Materials and Multi Layer Rotomolding Technology for Higher Barrier Performance of Rotomolded Tanks”, SPE - Rotational Molding by Design Conference, pp. 37-47.

Carlsen C and Partridge R (2007), “Petro- Seal TM Low Permeation Rotomolded Fuel Tanks”, ARM- SARD Conference, pp. 1-38.

Crawford R J and Nugent P J (1992), “A New Process Control System for Rotational Moulding”, Plastics, Rubber and Composites Processing and Applications, Vol. 17, 23-31.

Gogos G, Olson L G, Liu and Pasham V R (1998), “New Models for Rotational Molding of Plastics”, Polymer Engineering and Science, Vol. 38, 1387-1398.

Greco A and Maffezzoli A (2004), “Powder-Shape Analysis and Sintering Behavior of High-Density Polyethylene Powders for Rotational Molding”, Journal of Applied Polymer Science, Vol. 92, 449-460.

Greco A, Maffezzoli A and Vlachopoulos J (2003), “Statistical and Kinetic Approaches for Linear Low-Density Polyethylene Melting Modeling”, Advances in Polymer Technology, Vol. 22, 289-295.

Incropera F R, Dewitt D P, Bergman T L and Lavine A S (2006), “Introduction to Heat Transfer”,5th Edition, Wiley Publications.

Sarrabi S, Colin X and Tcharkhtchi A (2010), “Kinetic Modeling of Polypropylene Thermal Oxidation During its Processing by Rotational Molding”, Journal of Applied Polymer Science, Vol. 118, 980–996.

Tan S B, Hornsby P R, McAfee M B, Kearns M P and McCourt M P (2011), “Internal Cooling in Rotational Molding—A Review”, Polymer Engineering and Science, Vol. 51, 1683-1692.

Downloads

Published

2012-09-01

How to Cite

[1]
Raghav Bansal and Sachin Waigaonkar, “THERMAL ANALYSIS OF ROTATIONAL MOULDING PROCESS: AN APPLICATION TO MULTILAYER MOULDING”, JME, vol. 7, no. 3, pp. 158–163, Sep. 2012.