Modeling the Machining Parameters for Electro Chemical Machining of Aluminium Composites using RSM

Authors

  • Ravikumar R Dept. of Production Engineering, National Institute of Technology, Tiruchirappalli – 620 015, Tamilnadu, India
  • Asokan P Dept. of Production Engineering, National Institute of Technology, Tiruchirappalli – 620 015, Tamilnadu, India
  • Narendar Singh P Department of Manufacturing Engineering,Annamalai University, Annamalai Nagar, Chidambaram – 608 002.

Keywords:

Electro Chemical Machining (ECM), Material Removal Rate (MRR), Surface Roughness (Ra), Response Surface Methodology (RSM), ANOVA

Abstract

Electro Chemical Machining (ECM) allowed success in the production of newer materials, especially for the aerospace and biomedical applications. Using ECM technology, complicated cuts can be made through difficult – to – machine hard materials. This paper highlights the development of mathematical models for correlating the interactive and higher order influences of various machining parameters on the dominant the machining criteria, i.e., the material removal rate and the surface roughness through response surface methodology (RSM), utilizing relevant experimental data as obtained through experimentation. Validity and correctiveness of the developed mathematical models have also been tested through Analysis of Variance (ANOVA). The present work also highlights the development of mathematical models for analyzing the effect of various process parameters such as, current, voltage, flow rate and gap width on the material removal rate and surface roughness.

Downloads

Download data is not yet available.

References

Hocheng H., Kao P.S. and Lin S., 2004, Development of the eroded opening during electrochemical goring of hole“, International Journal of Advanced Manufacturing Technology, Vol 25, pp. 1105 – 1112.

Bhattacharyya B, Malapati M., Munda J and Sarkar A, 2006, “Influence of tool vibration on machining performance in electrochemical micro-machining of copper”, International Journals of Machine Tools & Manufacture, Vol 47, pp. 335 – 342.

Wuthrich R and Fascio V, 2004 “Machining of non-conducting materials using Electrochemical discharge phenomenon – an overview”, International Journal of Machine Tools & Manufacture, Vol 45, pp. 1095 – 1108.

Sarkar B.R., Doloi B., and Bhattacharyya B,2005 “Parametric Analysis on Electrochemical discharge machining of silicon nitride ceramics”, International Journal of Advanced Manufacturing Technology, Vol 28, pp – 873 – 881.

Yang C.T., Song S.L., Yan B.H. and Huang F.Y., 2006, “Improving machining performance electro chemical discharge machining by adding SIC to electrolute” ”, International Journals of Machine Tools & Manufacture, Vol. 46, pp. 2044 – 2050.

Jaganth Munda and Bhattacharyya B., 2006, “Investigation in to electrochemical micromachining (EMM) through response surface methodology based approach”, International Journal of Advanced Manufacturing Technology.

Bhattacharyya B and Sorkhel S.K, 1999, “Investigation for controlled electrochemical machining through response surface methodology – based approach”, Journal of Materials Processing Technology”, Vol. 86, pp. 200 – 207.

Ebeid S.J, Hewidy M.S., El – Taweel T.A. and Youssef A.H., 2004, “Towards higher accuracy for ECM hybridized with low – frequency vibrations using the response surface methodology”, Journal of Materials Processing Technology”, Vol. 149, pp. 432 – 438.

Douglas. C. Montgomery, 2004, “Design and Analysis of Experiments. 5th Edition. John Wiley & Sons. Inc, Singapore.

Downloads

Published

2008-06-01

Issue

Section

Articles

How to Cite

[1]
“Modeling the Machining Parameters for Electro Chemical Machining of Aluminium Composites using RSM ”, JME, vol. 3, no. 2, pp. 104–114, Jun. 2008, Accessed: Dec. 07, 2024. [Online]. Available: https://smenec.org/index.php/1/article/view/626

Similar Articles

1-10 of 555

You may also start an advanced similarity search for this article.