INVESTIGATION ON HOT TENSILE DEFORMATION BEHAVIOUR OF FRICTION WELDED DISSIMILAR JOINTS OF INCONEL 600 WITH AISI 304L AUSTENITIC STAINLESS STEEL
Keywords:
Friction welding, Inconel 600, 304L austenitic stainless steel, Dissimilar Joints, hot tensile propertiesAbstract
With the help of continuous drive friction welding process, the dissimilar joints of Inconel 600 with 304L austenitic stainless steel were fabricated. Hot tensile properties of these joints were evaluated by hot tensile test at the temperature range of 25ºC– 600ºC and strain rate of 0.001× s-1 as per ASTM E21 standard. The results showed that the highest ultimate tensile strength of 487MPa was achieved at the temperature of 300º C for smooth specimen whereas the lowest ultimate tensile strength of 437MPa was achieved at the temperature of 600ºC. The micro structural characteristics, micro hardness variations and fracture surface anlaysis were carried out to understand the deformation behaviour of friction welded dissimilar joints of Inconel 600 and AISI 304L stainless steel.
Downloads
References
Radoslaw Winiczenko and Mieczysław Kaczorowskib (2013), “Friction welding of ductile iron with stainless steel” Journal of Materials Processing Technology, Vol. 213, 453– 462.
Shah Hosseini H, Shamanian M and Kermanbur A (2011), “Characterization of microstructures and metallurgical properties of Inconel 617/310 stainless steel dissimilar welds,” Materials characterization, Vol. 62, 425-431.
Shanjeevi C, Satish Kumar S, Sathiya P (2013), “Evaluation of Mechanical and Metallurgical properties of dissimilar materials by friction welding” Procedia Engineering Vol. 64, 1514 – 1523.
Dieter G E, Khan H A and Semiatin S L (2003), “Handbook of workability and process design,” Materials Park: ASM International.
Kaneno Y, Takasugi T and Hanada Sh. (2001)., “Tensile property and fracture behavior of hot-rolled CoTi intermetallic compound” Mater Sci Eng A, Vol. 302, 215–221.
Hu J and Lin D L (2008), “Plastic deformation behavior in dual-phase Ni–31Al intermetallics at elevated temperature,” Mater Sci Eng A, Vol. 490, 157–161.
Du X and Wu B (2005), “Continuous dynamic recrystallization of extruded NiAl poly crystals during the superplastic deformation process” Metall Mater Trans A, Vol. 36, 3343–51.
Wang Jing zhong, zheng-dong Liu, Cheng shi-chang and Bao Han-sheng (2011), “Hot deformation behaviors of S31042 austenitic heat-resistant steel” Journal of Iron and steel Research, International, Vol. 18(10) 54-58.
Tanshu –Ping (2009), “Effect of composition and processing on properties and strengthening mechanism of S30432 steel (D).,” Procedia Engineering, Vol. 74, 1621 – 1631.
Morakabati M, Aboutalebi M, Sh.Kheirandish, Karimi Taheri A, and Abbasi S M (2011), “Hot tensile properties and microstructural evolution of as cast NiTi and NiTiCu shape memory alloys,” Materials and Design, Vol. 32, 406-13.
Lin Y C, Chen M S, Zhong J (2008), “Constitutive modeling for elevated temperature flow behavior of 42CrMo steel,” Comp Mater Sci, Vol. 42, 470–477.
Wu H Y, Zhu F J, Wang SC, Wang W R, Wang C C and Chiu C H (2012), “Hot deformation characteristics and strain-dependent constitutive analysis of Inconel 600 superalloy,” J Mater Sci., Vol. 47, 3971–3981.
Sathiya P, Aravindan S, Noorul Haq A (2007), “Effect of friction welding parameters on mechanical and metallurgical properties of ferritic stainless steel” Int. J Adv Manuf. Technol., Vol. 31(11), 1076–1082.
Fukumoto S, Tsubakino H, Okita K, Aritoshi M and Tomita T (1999), “ Friction welding process of 5052 aluminium alloy to 304 stainless steel,” Vol. 15, 1080–1086.
Shanjeevi.C., SatishKumar.S., Sathiya.P (2013), “Evaluation of Mechanical and Metallurgical properties of dissimilar materials by friction welding,” Procedia Engineering, Vol- 64, pp. 1514 – 1523.
Momeni A and Dehghani K (2010), “Prediction of dynamic recrystallization kinetics and grain size for 410 martensitic stainless steel during hot deformation,” Met Mater Int, Vol.16, 843–849.
Mirzaee M, Keshmiri H, Ebrahimi G R, Momeni A (2012), “Dynamic recrystallization and precipitation in low carbon low alloy steel 26NiCrMoV,” Mater Sci. Eng. A, Vol. 551, 25–31.
Lin Y C, Chen M S, Zhong J (2008), “Microstructural evolution in 42CrMo steel during compression at elevated temperatures,” Mater Lett, Vol. 62, 2132–2135.
Deng J, Lin Y C, Li S S, Chen J and Ding Y (2013), “ Hot tensile deformation and fracture behaviors of AZ31 magnesium alloy”, Mater Des, Vol-49, 209–19.
